Vehicle systems gathers in one place what the car reports about each system: the particulate filter and its regenerations, the traction battery and its cells, the electric motor, the engine, the transmission, brakes and stability, the 12 V battery and its alternator, the gas system and the hydrogen fuel cell. A tab appears for each system your car answers. Live values are read only while the tab is on screen.
Open a system
Open Vehicle systems on the Mechanic screen. The tabs at the top are the systems of this car: a diesel opens on the filter, an electric or hybrid car on the traction battery. Tap a tab to switch; the screen reads only the tab you are on and stops reading when you leave it.
With more than one car in the garage, the chip under the title picks the car. Another car shows what is saved for it; live values belong to the connected car.
Search for more sensors
The magnifier at the top opens Search for sensors: pick a system, and the app asks the car for the values of that system that the catalogs of your make know, and keeps the ones that answer. It needs the car connected and stopped and takes a few minutes; leaving the screen cancels it. A system the car answers gets its tab, and each card shows only the values the car confirmed.
When two sensors answer for the same value, a strip says so and the value shows a dot: tap it to choose the one this car uses.
Searching a system again replaces what the earlier search saved: values the car no longer confirms, and values the catalogs no longer have, leave; the ones it confirms again stay, with your choice.
Follow the particulate filter
On a diesel, the Particulate filter tab shows whether a regeneration is running now, how close the next one is (Toward the next regeneration), what happened since the last one and the filter's temperatures and pressure. Track regeneration opens Data recording with the filter profile ready.
Every regeneration the app sees is kept under Regenerations, with its duration and distance. One marked Probable was deduced from the car's counters between two connections. One marked Interrupted was running when the engine was switched off; the car resumes it on a later drive.
Get notified
The alerts are in Settings, under System settings. Regeneration alert tells you when the engine starts cleaning the filter, so you can keep driving until it finishes. Interrupted regeneration alert, a Pro feature, tells you when the engine was switched off in the middle of one. Both also appear on Android Auto and CarPlay.
Read the traction battery
On an electric or hybrid car, Read battery reads the voltage of every cell once, with the car stopped, and saves a report: the lowest and highest cell, the deviation between them, the cell furthest from the others and, when the car reports them, the resistance per block, the isolation and the charge counters. On the free plan it shows a short video first.
Open a report to see every cell; tap a bar to read that cell. PDF and CSV share the report, under the same rule as the other exports.
The tab also shows the pack's cooling (coolant inlet and outlet, heater), the charge of the fullest and the emptiest cell and, under Charging, the charging state, the charger temperature and the total charging time. When the car does not send the pack's power or the deviation between cells, the app computes them from the voltage, the current and the highest and lowest cell. Read battery appears only for cars whose catalogs can read every cell.
Check brakes and stability
The Brakes and stability tab shows what the car's brake and stability modules report: the speed of each wheel and the largest difference between them, the pedal and the brake pressure, the steering angle, the yaw rate and the lateral and longitudinal acceleration, whether ABS, stability or traction control is acting, the parking brake, the brake temperatures, the fluid level and the pads. Each card appears only with the values your car answers.
Check the 12 V battery
The 12 V battery tab draws the voltage on a chart while the tab is open, with the lowest and the highest reading. When other modules of the car also measure it, tap the value to choose which one to show. When the car reports them, the tab also shows the battery sensor (charge, health, current, temperature, capacity, draw with the car off) and the alternator.
Each drive adds two readings: before the start, with the engine off, and with the engine running. The 30-day chart shows the reading before the start of each drive, which tells how the battery holds overnight.
When the adapter was connected before the drive, the reading before the start is the adapter's own voltage with the ignition off, on every car. On hybrid, plug-in and electric cars the reading with the system on is taken once the car is moving, since the engine may never turn. On electrified cars the DC-DC converter card shows the converter that charges the 12 V battery.
Report a problem
Report a problem, at the end of each tab and in each battery report, sends what the tab shows and how the app read each value. It helps fix a value shown in the wrong card for your car.
- Tabs
- One per system the car has. Only the tab on screen is read.
- Search this car’s sensors
- Magnifier at the top: searches the catalogs of your make for a system's values. Car connected and stopped.
- Regenerating
- The filter is being cleaned now, with how long it has been running.
- Toward the next regeneration
- How close the filter is to the point where the engine starts a regeneration.
- Track regeneration
- Opens data recording with the sensors of the filter.
- Alerts
- Regeneration (free) and interrupted regeneration (Pro), in Settings.
- Read battery
- Reads every cell once and saves a report. Car stopped.
- The report on A4 pages, with every cell in a table.
- CSV
- One row per cell, with its difference from the average.
- 12 V battery
- Voltage chart, battery sensor and alternator, and the readings of each drive.